Brandneues Replacement Board für Bally/Williams DMD Controller Board.
Ersetzt A-14039 & A-14039.1
Plug and Play
Board funktioniert in diesen Geräten
Black Rose
Corvette
Creature from the Black Lagoon
Demolition Man
Dr.Who
Dirty Harry
Dracula BSD
Fish Tales
Flintstones
Getaway (HS2)
Gilligans Island
Hot Shots Basketball
Hurricane
Indiana Jones
Indianapolis 500
Jackbot (die letzten hatten WPC95 Boards,bitte vor Kauf kontrollieren)
Johnny Mnemonic
Judge Dredd
No Fear
Party Zone
Popeye
Road Show
Star Trek TNG
Terminator 2
The Addams Family & Gold
The Shadow
Theater of Magic
Twilight Zone
White Water
Who Dunnit
World Cup Soccer
The new XPin? XP-WPCDMD-CTRL uses the latest FPGA
(Field Programmable
Gate Array) technology to solve the design issues that
reside in the Williams
WPC-S and WPC89 dot matrix controller board.
The XPin? XP-WPCDMD-CTRL
replaces all 4 different versions of the D-14039
used in those generation games.
The FPGA circuit design fixes the timing issues associated
with the OEM design
which was due in large part
to the IC count and board layout. Utilizing this
FPGA technology, we have added additional test features
which will allow the end
user to verify that
this board is functioning as designed and providing an
independent method of testing the dot matrix display
outside of the game software,
helping the end
user to determine if a bad display is a bad display and not some
other component in the game.
The FPGA circuit design also allows for an increased
scan rate, which is needed
for LED based
dot matrix displays. Original OEM Plasma DMD?s, due to their
technology, have an effect called persistence.
Persistence is the time it takes
to go from an
ON state to an OFF state. Persistence in the OEM display?s lasts
~1/1000 of a second. The persistence of an LED is significantly
less then this.
The increased scan rate allows
for the LED to stay on for a longer period of time
and reduces the strobing effects associated with LED technology.
A redesigned High Voltage section provides a solid
foundation for the operation of
the OEM High Voltage
Plasma Dot displays. Centralized test points allow for easy
voltage measurements.
Though it is not necessary to change your OEM Plasma Display
to work with our
new XPin? XP-WPCDMD-CTRL
Controller, you can upgrade your old plasma
display to our new XPin? XP-DMD4096 LED DMD,
in your choice of colors ?
Red, Blue, Green, Orange,
Yellow/Green, or Amber (Amber is our color matched Plasma Orange)
Features
Re-Engineered High Voltage section, eliminating shortcomings
in the original OEM design. Debug system independent
from the original game firmware. Allows the user to
verify the functionality of the Controller and dot matrix Display
independent from the game MPU and Firmware.
Multi-rate Scanning. Research has shown that different
games and even different firmware revisions for the same
game can have slightly different scan rates. XPin? has
developed a system to adjust the scan-rate of the
dot matrix display to reduce the flicker that is often times visible
in OEM plasma displays and LED dot matrix displays. Increasing
the scan rate allows for smoother animations.
This multi-rate scanning is part of our Patent Pending
Light Wave Technology.The XPin? XP-WPCDMD-CTRL has a
dipswitch for additional functionality.The table below defines
what is available. When referencing SCAN RATE,the DMD
display has a certain refresh rate that is dependant on
factors suchas Game firmware and firmware revision.
Though not easily seen with theoriginal OEM plasma displays,
with LED displays these variations of scan ratescan be
noticed during normal game operation, causing a ?flickering?
effect.XPin? LightWave Technology, utilizing innovative
hardware circuit design,mitigates this effect by allowing the
user to increase the scan rate of thedisplay. Not all games
will require the 4x Scan Rate setting, but it is a
userpreference.Installation
Installation Time: About 20 minutes
Tools Required: 1/4? Nut-driver, Phillips screwdriver
1. Unplug the AC power from your pinball machine. Remove
game backglass.Open back box.
2. Remove OEM WPC DMD Controller board
3. Install the XP-WPCDMD-CTRL in the back box
4. Connect all connectors as indicated. Make sure to connect all ribbon cables with proper Pin 1 orientation
5. Double-check all connections, plug in the machine, and turn the game on.
6. All systems should be operational! Play on!